Industrial Valve Automation Oil/Gas Pulp/Paper Chemical Pharmaceutical Bio-Fuel University/College Power

PULP & PAPER INDUSTY

J Flow Controls is committed to provide the right valve for the pulp and paper industry.

J Flow Controls makes specialty valves out of special metals for corrosive applications in the Pulp and Paper. J Flow also provides automated valves for high cycle applications, where the valves turn every minute, 24 hours a day. J Flow also offers direct mount valves in two-piece, three pieces, flanged and three ways, four ways to where you can mount electric or pneumatic actuators directly to the stem of the valve. This eliminated the bracket and coupler, which saves the customer money and allows the customer to install the automated valve in tight areas.

J Flow™ 2-Way Ball Valve Spring Return Handle, Series SR

J-Flow's SR Series, spring return handle (also called dead man handle) was well designed as a heavy duty type for long term operation. The most characteristic of the SR Series is the locking device option.

The SR Series is designed to mount upon the ISO 5211 direct mounting pad. This will be convenient to replace a standard handle to a SR series. It is easy to replace the handles after long term service without discarding the entire valve. It is also economical to stock the spring handles separately.

• Specifications:
  • Stainless Steel spring handle
  • Heavy duty design
  • For ISO 5211 direct mounting pad
• Option:
  • Locking Device

^top

Double Seated Glove Control Valve with Top and Bottom Guide | Series 1000

Promotes tightness and heavy duty control.

• Flow Direction : Flow to Open or Flow to Close
• Max. Fluid Temperature : 1049°F
• Min. Fluid Temperature : -320°F
• Seat Leakages : ANSI B16.104 Class IV
  • Option 1: ANSI B16.104 Class V for Metal Seat Tight Shut off
  • Option 2: ANSI B16.104 Class VI for Teflon Soft Seat & Seal (-22°F ~ 446°F)
• Body: Double Seated Top and Bottom Guide
• Bonnet Type: Stud Bolted
  • Standard Type: -0.4°F ~ 536°F
  • Extension Type: 538°F ~ 1049°F & under -0.4°F
• Flow Characteristics : Linear, Equal Percentage, Modified %
• Cv Ratio: 50:1
• Diaphragm actuators enclosed, heavy duty Cylinders(spring-cylinder and double-cylinder) available
• Applicable for various instruments(positioner, SOV, limit switch)

^top

Single Seated Glove Control Valve with Top Guide | Series 2000

Promotes tightness and heavy duty control.

• Flow Direction: Flow to Open or Flow to Close
• Max. Fluid Temperature: 1049°F
• Min. Fluid Temperature: -320°F
• Seat Leakages: ANSI B16.104 Class IV
  • Option 1: ANSI B16.104 Class V for Metal Seat Tight Shut off
  • Option 2: ANSI B16.104 Class VI for Teflon Soft Seat & Seal (-22°F ~446°F)
• Body: Globe Single Seated Top Guide
• Bonnet Type: Stud Bolted
  • Standard Type: -0.4°F ~ 536°F
  • Extension Type: 538°F ~ 1049°F & under -0.4°F
• Flow Characteristics: Linear, Equal Percentage, Modified %, Semi-Throtle
• Cv Ratio: 50:1
• Diaphragm actuators enclosed, heavy duty Cylinders (spring-cylinder and double-cylinder) available
• Applicable for various instruments (positioner, SOV, limit switch)

Contoured Trim (Thread & Quick Change Trim)

The contoured plug is design with a specially represented valve plug head. The plug head represent defines the flow characteristic through the valve, and offers a smooth profile to the flow leading to a high pressure recovery. The trim is most suited to low pressure drop application and is used in the majority of control applications.

Contoured Soft Seat Trim

An alternative of the standard contoured plug is the soft seated option. The plug head is manufactured with a clamped on shroud which locks the soft seated ring in position. When the soft face contacts the seating point it deforms the softer ring ensuring a high degree of closure. The soft faced plug is used on applications where bubble tight shut off is required.

Tendril (Multi-hole, Multi-stage) Trim

The trim design presented is a multi-stage, multi-hole trim. There are 1 ~ 5 Stage designs available depending on pressure drop and potential for cavitation. The fluid passes through the flow path generated by incorporating angled flats onto the surface of the plug, together with a cut out on the internal diameter of the seat. The pressure drop is apportioned across the stages of letdown so that the pressure drop progressively reduces as it passes through the stages of the trim. This gives excellent resistance to cavitation on high pressure drop applications. For very high pressure drop applications the plug and seat insert would be manufactured from tungsten carbide or glass metallic optionally.

Multi-Grooved (Cascade) Trim

Cascade trim for non-compressible fluid applications is designed for any number of grooves of required pressure drop to meet the specifications for preventing cavitation from occurring and eventual erosion. There are 8~9 grooves designs available depending on pressure drop and potential for cavitation. The fluid passes through the flow path generated by incorporating angled flats onto the surface of the plug, together with a cut out on the internal surface of the seat. The pressure drop is apportioned across the stages of letdown so that the pressure drop progressively reduces as it passes through the grooves of the trim. This gives excellent resistance to cavitation on high pressure drop applications. For very high pressure drop applications the plug and seat insert would be manufactured from tungsten carbide or advanced glass metallic optionally.

Micro Trim

The micro trim designs a seat guided construction, capable of handling high pressure drops, without instability problems. This trim design has an inherent flow characteristic of Linear of Modified Equal Percentage, and has excellent rangeability. It is an ideal selection for the control of very low flow rates. For very high pressure drop applications, or flows which would have potential cavitation, there are multi-stage options of this design (5 stages maximum), and there are also applicable tungsten carbide and advanced glass metallic options for pressure drops greater than 1450 psi.

^top

J Flow™ DM2500 Series Direct Mount Cavity Filled Flanged Ball Valve

Direct mount two piece and one piece ANSI 150 & 300 flanged ball valve.

• Advantage: Direct Mount, Blow-out proof stem, silicone free, Live loaded Packing, Anti-static, heat codes
• Size:  Ranges from 1/2” to 12”
• Service:  Well suited for Steam, Thermal Fluids, Oxygen, Dry or wet Chlorine, industrial Applications and hydraulic applications
• Options:  ISO 5211 mounting pad so extended bonnet, electric and pneumatic actuators can mount easily, Special Alloys are available, ANSI 150 & 300, full port or reduced port, steam jackets and spring handles

^top

J Flow™ OB2500 Series Two Piece High Performance Flanged Ball Valves

An ANSI 150 or ANSI 300 two piece direct mount flanged high performance ball valve, with an orifice in the ball.

• Advantages:
  • The orifice allows for better control of media in the pipeline.
  • The seat is encapsulated in a metal ring, which prevents the seat from cold flow.
• Standards: ASME B16.34 rated
• Size: Ranges from 1/2” to 12”
• Options:
  • 15, 30, 45, 60 and 90-degree balls
  • The ends can be ANSI 150, or ANSI 300
  • The valves can be NACE certified
• Special Alloys

^top

J Flow™ 3000 Series Globe Angle Control Valve

• Flow Direction: Flow to Open or Flow to Close
• Max. Fluid Temperature: 1049°F
• Minimum Fluid Temperature: -320°F
• Seat Leakages: ANSI B16.104 Class IV
  • Option 1: ANSI B16.104 Class V for Metal Seat Tight Shutoff
  • Option 2: ANSI B16.104 Class VI for Teflon Soft Seat & Seal (-22°F ~ 446°F)
• Body: Globe Single Seated Top Guide
• Bonnet Type: Stud Bolted
  • Standard Type: -0.4°F ~ 536°F
  • Extension Type: 538°F ~ 1049°F & under -0.4°F
• Flow Characteristics: Linear, Equal Percentage, Modified % & Semi-Throttle
• Cv Ration: 50:1
• Diaphragm actuators enclosed, heavy duty cylinders (spring-cylinder and double-cylinder) available
• Applicable for various instruments (positioner, SOV, Limit switch)

^top

J Flow™ 3500 Series Two Piece 2,000 PSI Ball Valve

Full port design for maximum flow, carbon filled seats for 250 PSI of steam, B16: 34, Anti-Blow Stem, Seats self compensate for wear, temperature and pressure, Standard slide-lock handle meets OSHA 1910.147.

• Applications: Hydraulic, Steam and fluids
• Size: Ranges from 1/4” to 2”

^top

J Flow™ 3500 Series Globe Valve - 3 Way Mixing / 3 Way Diverting

1" to 10" body size, ANSI Class 150-600 with flanged, butt-weld, or socket-weld ends. Available in Carbon Steel or Alloy Steel or Stainless Steel body materials. Automated with Diaphragm and Cylinder Actuators with/without Handwheels. Positioners, Instrument Valves, Limit Swithces and Solenoid Valves are available.

• Flow Direction: Mixing, Diverting
• Max. Fluid Temperature: 1049°F
• Minimum Fluid Temperature: -320°F
• Seat Leakages: ANSI B16.104 Class IV
  • Option 1: ANSI B16.104 Class V for Metal Seat Tight Shutoff
  • Option 2: ANSI B16.104 Class VI for Teflon Soft Seat & Seal (-22°F ~ 446°F)
• Body: Globe Single Seated Top Guide
• Bonnet Type: Stud Bolted
  • Standard Type: -0.4°F ~ 536°F
  • Extension Type: 538 °F ~ 1049°F & under -0.4°F
• Flow Characteristics: Linear, Equal Percentage, Modified %
• Cv Ration: 50:1
• Diaphragm actuators enclosed, heavy duty cylinders (spring-cylinder and double cylinder) available
• Applicable for various instruments (positioner, SOV, Limit switch)

^top

J Flow™ 3700 Series Two Piece 1,000 PSI Ball Valves

A two piece ball valve with full port design and Teflon seats

• Advantages: special pricing, on-off service
• Size: Ranges from 1/4” to 3”
• Service: manual service only, locking handle meets OSHA 1910.147
• Oval handles and locking oval handles are available

^top

J Flow™ DM3800 Series Two Piece Direct Mount 1,000 PSI Ball Valves

Two piece direct mount

• Advantages: full port, Teflon seats, special pricing, Blowout proof stem, Self-adjusting V ring stem packing, NACE MRO175-90, Vacuum service to 20 microns, on-off service, live loaded packing, NACE certified, Heat codes stamped on the valve is a standard, low torque
• Size: Ranges from 1/4” to 2”
• Options: RNPT ends, Metric and spring handles
• Service: Hot and cold water, compressed air and natural and bottle gas

^top

J Flow™ 4000 Series Globe, Heavy Duty Cage Balanced Low Noise Anti-Cavitation

• Flow Direction: Flow to Open or Flow to Close (Pilot & Un-Compressible Fluid)
• Max. Fluid Temperature: 1049 °F
• Minimum Fluid Temperature: -320 °F
• Seat Leakages: ANSI B16.104 Class IV (Soft Seal), Class III (Metal Seal)
  • Option 1: ANSI B16.104 Class V for Metal Seat Tight Shutoff (only Pilot Type)
  • Option 2: ANSI B16.104 Class VI for Teflon Soft Seat & Seal (-22 °F ~ 446°F)
• Body: High Capacity Globe Cage Guided
• Bonnet Type: Stud Bolted
  • Standard Type: -0.4°F ~ 536°F
  • Extension Type: 538 °F ~ 1049°F & under -0.4°F
• Flow Characteristics: Linear, Equal Percentage, Modified % & Semi-Throttle
• Cv Ration: 30:1 (Tendril), 50:1 (Reduced Cage), 100:1 (Full Cage)
• Diaphragm actuators enclosed, heavy duty cylinders (spring-cylinder and double-cylinder) available
• Applicable for various instruments (positioner, SOV, Limit switch)

^top

J Flow™ DM4500 Series Three Piece Direct Mount 1,000 PSI Ball Valves

Direct Mount three piece In Line repairable valve

• Advantages: Full port, Super Teflon seats, special pricing, on-off service, live loaded packing, NACE certified, Silicone free, Heat codes stamped on the valve is a standard
• Size: Ranges from 1/4” to 4”
• Service: Steam, Air, Water and Chemicals
• Options: NPT ends, Metric, Socket or Butt Weld, Flanged ANSI 150 and 300, Monel, Alloy 20, Duplex, Hastalloy and Spring Handles
• Oval handles and locking oval handles are available

^top

Three-Piece Double Block and Bleed Ball Valve | Series DB4600

• Features & Benefits:
  • Three piece high performance ball valve
  • Body and end caps quality investment casting
  • Available in stainless steel, carbon steel and alloys
  • Blow-out proof stem design
  • 100% air tested under water at 80-100 psi
  • Working pressure: 2000 WOG
  • Temperature range: -20° to +600°F
  • ISO 5200 direct mounting pad
  • Locking device
  • 2000 psi
• Size:
  • Ranges from 1/2" - 2"

^top

J Flow™ DM4600 Series Three Piece Direct Mount 2,000 PSI Ball Valves

High quality three piece full port valve, 2,000 PSI, meets B16:34.

• Advantages: Full port, Super Teflon seats, B16:34, on-off service, live loaded packing, NACE certified, Silicone free, Heat codes stamped on the valve is a standard, Ideal for both on-off and control services
• Size: Ranges from 1/4” to 4”
• Service: Excellent in Steam service, Fluid, Vacuum service, Oxygen, handling petroleum products, flammable or hazardous services, corrosive services and normal services
• Options: NPT ends, Metric, Socket or Butt Weld, Flanged ANSI 150,300 & 600, Monel, Alloy 20, Duplex and Hastalloy and pigging valves are available

^top

J Flow™ 9000 Series Control Choke Vavles

• Features and Benefits:
  • Flow Direction: Flow to Open or Flow to Close
  • Max. Fluid Temperature: 1049°F
  • Minimum Fluid Temperature: -320°F
  • Seat Leakages: ANSI B16.104 Class IV or V
  • Body: Angle or Straight Globe
  • Bonnet Type: Stud Bolted
  • Flow Characteristics: Linear, available Equal Percentage and Modifed %
  • Cv Ration: 30:1 to 800:1
  • Diaphragm actuators, heavy duty cylinders (spring-cylinder and double-cylinder), electric motors
  • Applicable for various instruments (positioner, SOV, Limit switch)
• Size: Ranges from 1 1/2” to 10”

^top

J Flow™ 9400 Series Top Entry (3 piece Firesafe) Valves

• Design Features:
  • Full port 1/2" - 10"; Regular port 1/2" - 12" threaded, socket weld, butt weld, and flanged ANSI 150 - 2500
  • Seats compensate for wear and fluctuations of pressure and temperature
  • Multiple solid cup and cone type PTFE stem seal or graphite packing
  • Two-piece self-aligning packing flange and gland
  • Stem guides in cover and gland bushing eliminate side thrust
  • Longer cycle life
  • Lower, uniform torque
  • Blow-out proof stem
  • Live-loaded thrust washer prevents galling and provides a secondary stem seal
  • Meets ASME B16.5, B16.10 and B16.34, API 608, API 598, API 607 Rev. 5/ISO 10497
  • Fully-enclosed spiral wound graphite filled stainless body gasket
  • Permits in-line access for seat replacement
  • ASME Section 8 cover/body flange connection and bolting provide high sealing integrity of body gasket
  • Body-cover joint not affected by pipe stresses
  • Wall thickness complies with ASME B16.34
  • Can be welded into line without disassembly
  • Stainless steel trim on all valves including handle
  • Oval handles with locking devices, as well as extensions available
  • Ball-to-stem only (2" full port and larger) and stem-to-body static ground
  • Locking devices standard
  • Tapping for mounting actuators standard
  • AGA and CGA approved, regular port, thread ed ends (optional) 1/2" - 2"
  • Valves can meet NACE specifications for sour gas service when required
  • Optional topworks:
    1. Live-loaded single or double packing
    2. TA-Luft certified when supplied with PTFE live-loading packing (optional)
    3. Bellows seal design
  • Fire tested in accordance with API 607 Rev. 5/ISO 10497

^top

J Flow™ 9600 Series Flanged Ball Valve

The 9600 series is a line of flanged valves that include a floating ball. The valves are available in ANSI 150 and ANSI 300.

• Advantages: 
  • Contains live loaded packing which allows for adjustment of the stem
  • Reliable seat seal
  • Fire safe
• Size: Ranges from 1/2” to 12”
• Standards: ASME B16.34 rated
• Options:
  • Available in reduce or full port
  • Can be NACE certified
  • Soft seated or metal seated

^top

J Flow™ 9700 Series Trunnion Ball Valve

• Advantages:  Well suited for gas distribution, gas transmission, oil field production, industrial applications and hydraulic applications
• Size:  Ranges from 1/2” to 60”
• Double block and bleed
• NACE certified, API 6D certified, Fire safe to API 607 4th edition
• Full port, reduced port, B16:34
• LCB, LF2, A103, 316, F316, A216

^top

J Flow™ 9800 Series Trunnion Valves, Metal Seated Valves

API 6D, blow-out proof stem, fire safe to API 607, 4th Edition

• Advantages: Well suited for ash/water slurry, aluminum catalyst, bottoms recovery, coal slurry, flue gas, heavy oil with catalyst fines, diesel dereivative, hydrocarbons, pump isolation, and tar sludge
• Size: Ranges from 1/2” to 60”
• NACE certified
• API6D certified
• F11, F22, A103, A216, 316, F316, LF2, LCB

^top

J Flow™ 9900 Series Segmented Ball Valve

The 9900 series segmented ball valve, control valve for regulating media flow capacity.

• Advantages: this valve is a key product for the ethanol industry because:
  • The valve has lower torque, which reduces likelihood media, will get trapped
  • The valve is excellent in controlling fluid, steam, water, air and other substances
• Size: Ranges from 1” to 30”
• Options: The valve body can be wafer style or can include ANSI 150, ANSI 300 or ANSI 600 flanges

^top

J Flow™ OB4600 Series Three Piece High Performance Ball Valve

The J Flow™ OB4600 series is a 2,000-PSI, three piece high performance ball valve, with an orifice in the ball.

• Advantages: 
  • The orifice allows for better control of media in the pipeline.
  • The seat is encapsulated in a metal ring, which prevents the seat from cold flow
• Standards: ASME B16.34 rated
• Size: Ranges from 1/4” to 4”
• Options:
  • Available with 15, 30, 45, 60 and 90 degree balls. 
  • The ends can be threaded, socket welded, butt welded, ANSI 150, or ANSI 300
  • The valves can be NACE certified
  • Special Alloy are available

^top

» View additional ball valve and valve automation control products offered by J Flow